MIKROTIK ROUTER BRIDGE SETUP PASSWORD IS NOT
MIKROTIK ROUTER BRIDGE SETUP DOWNLOAD AND INSTALLATION

Ive recently installed a RB4011 and Ive setup VLANs on the bridge with the bridge filtering on.Connect your computer using LAN cable from the Ethernet port on your Laptop PC to the PoE In port on the Mikrotik router. Here is my personal list of pros and cons:MikroTik RouterBoard RB4011iGS+RM Ethernet Router. It can be configured using a GUI (web browser, WinBox), CLI (SSH or Python RouterOS API).

Mikrotik Router Bridge Setup Download And Installation

MikroTik Community discussions. The download and installation process of the MikroTik RouterOS is described in the following.47) and a DrayTek Vigor Router. Logging into the MikroTik Router.

Remember that information sxachanged between the router and the management station is sent as plain text over an unsecured wireless network. The ESSID is MikroTik-E316BB. Connect to hAP acВі via Default Open WiFi networkConnect to the router via a default unsecured wireless network. After that you can connect provided antennas to the device and enable device.Picture 2 - Mouting Plate for Horizontal Position2.

Mikrotik Router Bridge Setup Password Is Not

Select either Dual Home AP Dual or WISP AP modes.Dual Home AP is the the default Access Point configuration page for most home users, which provides fewer options and simplified terminology. Click the Quick Set button in the right corner of router administration page and select preferred Quick Set mode. Therefore, the client should obtain an IP address from the router if DHCP client is running on the client.MikroTik hAP acВі provides a Quick Set button that allows you to configure the device with just few clicks. DHCP server is enabled on the router. Username is admin and the password is not set.

The group full is almost identical to the group write but also has ftp and policy policies (Picture > user group printSo far, we have working connection from LAN network to the router IP 192.168.88.1. Changing Default Password for Admin AccountW will set a password for the admin > user set name=admin password=here_you_type_secret_passNote: If you want to create a new user john and set the IP address the user john is allowed to login from, just > user add name=john group=full password=secret_string address=192.168.88.251To list all users type the command below (Picture > user printWe have assigned user john to the default group full which is one of the default groups read/write/full. Nevertheless, I strongly recommend you to use the wizard in case you are not a network guru or just want to speed up the configuration process.4.

So I logged in to the device using a browser and started the SSH service from the menu (IP-> Services-> ssh) by clicking the Enable button.Picture 8 - IP Address 192.168.88.1 Configured on Bridge InterfaceThe default wireless network installed is insecure, so we need to set up WPA2-PSK. While troubleshooting, I realized that the web interface was working. Therefore, I restarted the device, but the connection to the router did not work yet. Remove the IP address from the interface ether2 with the > ip address remove 0At this point, I lost my network connection with the router. Only the interface ether1 (WAN interfaces) is not connected to the > interface bridge port printPicture 6 - Interfaces Assigned to Bridge InterfaceThe correct approach is to configure IP address 192.168.88.1 on the bridge interface and remove the IP address from the interface > ip address add interface=bridge address=192.168.88.1/24 broadcast=192.168.88.255 netmask=255.255.255.0 network=192.168.88.0 comment='default gw address for LAN'Picture 7 depicts IP address configuration.Picture 7 - IP Address Configuration for All InterfacesNotice, the IP address 192.168.88.1/24 is configured for the both interfaces ether2 and bridge.

The list allows to define set of interfaces for easier interface management in different interface based configuration sections such as Neighbor discovery, Firewall, Bridge and Internet > interface list member printPicture 10 - I nterface Ether 1 Assigned To WAN ListTo connect the router to the Internet using pppoe protocol, create a new interface ppoe-client and associate the WAN interface ether1 with the pppoe-client > interface pppoe-client add interface=ether1 name=pppoe_int password=enter_pass_here use-peer-dns=yes > interface pppoe-client enable pppoe_intHheck the status of the pppoe interface with the command below (Picture > interface pppoe-client monitorPicture 11 - Checking PPPoE Interfaces StatusWe also need to add a firewall rule source nat in order to hide local addresses to public IP > ip firewall nat add chain=srcnat action=masquerade out-interface-list=WANAt this point, we should have be able to connect from the client to the Internet.The device has firewall already enabled and it is fully operational. That is why, it is definitely a good ideaDo disable unused > ip service disable > ip service disable > ip service disable > ip service disable > ip service disable winboxThe interface bridge is listed in the LAN list and the interface ether1 is listed in WAN list (Picture 10). To do so, we must create our root Certificate Authority (CA) on MikroTik, generate the certificate and sign the certificate with a private key of root CA.Create own Certification > certificate add common-name=LocalCA key-usage=key-cert-sign,crl-signSign Newly Created CA > certificate sign LocalCACreate a New Certificate for Webfig (non-root > certificate add common-name=192.168.88.1 days-valid=3650 name=WebfigEnable > ip service set allows unauthenticated remote attackers to read arbitrary files and remote authenticated attackers to write arbitrary files (CVE-2018-14847). To encrypt traffic between the router and the management station we need to enable TLS. We will assign the security profile my home wifi to both interfaces with the same ssid internethome1 (Picture > interface wireless set 0 security-profile='my home wifi' mode=ap-bridge > interface wireless set 1 security-profile='my home wifi' mode=ap-bridge ssid='internethome1'Picture 9 - Wireless Interfaces Configured for WPA2-PSKBy default, MikroTik web interface is only available via HTTP. The interfaces wlan1 is for the band 2ghz-b/g/n and interface wlan2 is for the band 5ghz-a/n/ac.

The most important rules are explained below. In our case, ether1 and pppoe_int are assigned in to WAN and the bridge is in the LAN list.